Відео

I made such a table. It works very well!

Loves it!

Clever solution. My company has been at work on a PAPR with an all in one design monocoque manifold. It has Lithium ion with smart charging onboard. Our aim is a PAPR that's more accessible to the DIY crowd. When we have certification, would you be willing to give it a try to compare? Its called MicroClimate Air3.

Perfect my friend. Thanks 😊

Comment

Thank you, have the kit. Going to class am!! I am ahead of class!!

Home depot has this box which is $167.00 now. I was considering this exact same idea and glad to see it worked out for you. I am sure it will be great for me as well.

Nice job

I love it! thank you Mr. Lundgren

Gary, Awesome video but I think I will need to watch it a few more times to fully understand what you were doing with this. I like your zero clearance tweak. It just makes more sense. If you haven't already, could you make a taper jig video using the Micro Jig system? Best regards.

Hi Very Nice Wine Bottle Holder

Well done. I got this thing and had no clue how to use it.

I’m going to miss you Gary. 😥 R.I.P

How do I purchase your plans for the work Sharp station

Thank you uncle gary, saved my vication with my girl

But how do I get the carriers backnon correctly

Well done! As a newbie, your video was very informative.

As a newbie, your video was very helpful!

hold the camera steady

Hello Gary! I have the same bandsaw and the Porter Cable riser kit. Did it increase your saw capacity to 105½" blade length or 105" blade lenght? As I said I have the same saw and riser kit. But have yet to install it on my saw. Thanks!

Well done -- Thanks! HF now offers sort of an upgraded version (basically identical except knobs are black now), Bauer 20105E-B in a black and red box and still low cost, especially on sale. These are really well made and powerful robust bargains (Gems for sure).

Thanks uncle Gary. I sincerely appreciate you❤

Someone needs to invent a nipple attachment that connects perfectly to a beer bottle. Like what you get on baby bottles lol.

Very helpful. I’ve been looking to confirm my choice of glue for fastening rare earth magnets to wood. I was considering CA glue, but didn’t thing the bond would last. I just about settled on epoxy when I saw your video. Thanks for this tip & the others you presented.

Thank you

Good tutorial. Thank you!

Install square to the saddle, not level. I can just see someone pulling out a torpedo level. Lol

Thats a mighty fine job on that router lift extention table , I like the removable power stop switch for your work table . Great idea thanks

screwdriver pry off tip works! thank you

Thank you for sharing your awesome project with us. Everyone stay safe, warm, happy and healthy. From Henrico County Virginia

Tnks ❤

Beautiful job! I would like to make my own but need to source the individual pieces. Do you know what the name of the metal piece that the razor head screws into the handle is called? And what the end metal piece of the handle is called?

Thanks for the video. Lots of great tips that can be used for other projects including the ice scoop kit as well.

does it really need a new spring? Mines a delta.

Hi Gary. I love this plan. I've been upgrading my 40 yr old craftsman bandsaw (installed carter guides and new tires) and now would like to build a new table that has a fence and standard miter slots for a miter gauge and a thin stock rip guide (with bearing) as my saw has only one miter slot and it is undersized. My question for you is what was the size you cut the slot for the incra miter gauge and could you put another one perpendicular to serve as a cross cut miter slot? Thanks, Liz

I have a similar set up (T3650) and am changing it. After 2 yrs, the extra weight of the router on the wing is causing the table to list. wood deck floor makes extra legs not the best option. While I like having the router in the wing, the sagging saw deck is annoying and has to be fixed. Throws off the fence calibration just a little bit. A trim size router would be ok, not cause the whole deck to list. I will be going back to the independent table for my big router and just keep the assembly for the trimmer size device.

BTW that wider area on the mitre slot is to keep your jig from flipping off of your tool if too much weight is put on the outer edge of the jig. Its a t track.

Nice job. I'm a little concerned about mounting the heavy table to the underside of the fence. Any problems with deforming the tracks?

I really like this idea especially the short hose. Due to the rotating air inside the can I think the exhaust hole would need to be in the center of the lid where there is the least amount of chips due to centrepital force. Then attach a filter over the exhaust hole to catch fine dust.

Thank you gary for doing this video. It helped me set up my quick change adapter that came from Bosch with no instructions. I guessed it right but the centering was something I did not do first. Likely saved me from screwing up some material.

I don’t know why people keep using a shop vac. You’re not supposed to, it actually makes it harder for the blower.

@8:56 When you slide the new spring and square nut back in, the nut fits nicely in place.. On mine the original spring seems to be longer and no matter what I try, I can't get the square nut to fit.. I've ordered a new spring and I am hoping that fixes the problem.. Thanks

After watching this video I decided to order the Duplicator from PSI. Also bought pen, bottle stopper, and chess set templates. Can't wait to get them in. Plan to use an idle mini lathe as a dedicated setup for this device. Thanks Santa and others for the Christmas gift cards and cash that I used to purchase this setup, and thanks, Gary, for doing the video!

👍👍👍👍

Bro you have no idea thank you, you saved christmas. My dumbass thought that the hole was for your finger.

this battery can be overcharged? i charge it over 24 hrs first day when i bought it...and the wall charger light always red i don't even know when battery is full. how many hrs charging can overcharged the battery? or not enough charging?

Thanks Gary for the great video ! Ijust bought this template guide and Idid subscribed

Perfect and thorough demonstration. Gonna order that kit for mine today.

Where do you get your patterns?

There are a lot of videos out there going through the basics of making band saw deers. I really enjoyed yours. Seeing you batch these out and the use of the Sharpie paint markers were nice spins on the process. Thank you!